640152 Carburetor for Tecumseh 640152A 640023 640051 640140 640152 HM80 HM90 HM100 8-10 HP Engine Snow Blower Mower 5000w Generator (with 33268 Air Filter+ Spark Plug+fuel line)
Product Description
Related Youtube Videos
33268 Air Filter for Tecumseh 33268 33263 HM70 HM80 H80 VM80 HM100 HXL840 TVM195 7HP 8HP 10HP engines
Carburetor replaces Tecumseh HM80-155638S, HM100-159409P, HM100-159402P, Tecumseh Models HM80 HM90 HM100 LH318XA LH358EA, fits 8hp 10hp snow blowers; Coleman Powermate Generator PM0525312 carburetor replacement
Please check before purchasing to make sure it will work for your needs
Package list: 1x carburetor, 1x gasket, 1x fuel line, 4x clamps, 1x spark plug,1x 33268 Air Filte
Related Searchs
Top Reviews
-
Robert DuPre
2025-02-04T00:00:00We were given a 5,500 watt generator by a friend who said, "you can have it for parts. Good luck getting it running." He had left if with stale fuel in his garage for years. All it needed was to replace the varnished up carb. So for what we paid for this carb, which was not much BTW, we now have a perfect running B&S generator, usually costing nearly $1,000! -
J. K. McConnell
2024-06-11T00:00:00My 25+ year old generator has been hard to start for years. It is 10 hp and pull start and many times I have to pull for dozens of times then take a break and start again. It is a bit tedious to get to a couple of the bolts but not too bad. Worst part is the generator is so big I had to work on it on the garage floor and could not see underneath for one of the bolts.
-
wanda Lou
2023-12-19T00:00:00Install this carburetor on a 10hp Tecumseh driven generator. I exchanged the plastic float with the old carburetor metal float since that one allowed me to adjust the float level at the needle thus allowing for a higher gas level in the bowl. Before doing this the engine would only run with the choke half close since there is not an adjustment to enrichen the fuel going into the engine. Now it runs perfect. I realize one has to have working knowledge of carburetors to make this changes but for the little money I paid for this carburetor I am very please with the results. Product was as advertised and it arrived sooner than I expected and yes I would order from this seller again.
-
wheeling365
2023-03-14T00:00:00Fit my generator with no issues. Quick and easy install without the mess and frustration of cleaning an ethanol damaged carb.
-
Jason P. Peters
2024-10-26T00:00:00First great but idles extremely high, can I get the setting for the top screw and the one in the middle ?
-
terry r howard
2023-11-12T00:00:00I received this item in the time frame they stated. But when I put it on my generator it still would not start. I took the air filter off and gas was pouring through the air filter housing. So I tapped on the bottom of the bowl lightly thinking the float might be sticking and that stopped it from leaking but still would not start the generator. I did not say anything to them about this because they are relatively cheap and did not want to have to go through the hassle of sending it back. So I just bought another one from someone else. That one came basically in the same packaging so I'm thinking they might be getting them from the same place. The reason I bring that up is because although it worked and the generator is running now. The bolt holes where you put the cover guard only had one hole drilled and it wasn't threaded and the other hole wasn't even there. But I made it work because like I said before I needed the generator and did not have time to waste sending it back. So I cannot recommend this carburetor in good conscience.
-
Penny
2024-11-05T00:00:00Work out perfectly good product
-
John Libonati
2020-09-04T00:00:00I ordered this carb for a 10 HP Tecumseh engine on a 6250/5000 generator. The carb looks almost the same as the original, but the throttle plate holes (I used the middle of the small holes) is too small in diameter. I drilled it to fit the governor linkage. The bolt holes in the side of the carb that hold the bracket that the shield plate attaches to were not tapped. They were also too small in diameter for the bolts. The left one cracked slightly and had to JB Weld it. The carb fits perfectly and is easy to install otherwise, but once I started the engine, it surged annoyingly. I removed the low speed jet and drilled it out to .6mm. That seemed to help, but it still missed. I drilled to .8mm which brought back the surging. I took the old jet out of the old carb and put it into this carb. The engine ran perfectly afterward. If you aren't a mechanic, you might want to try an OEM carb over this one.
-
Lino Molina
2023-09-07T00:00:00Me gustó el precio y que funciona bien, lo utilizo en un motor tecumseh de 10 hp